1. How do I add/delete a user code on my 264 Deadbolt? - Kwikset
1. Enter your Programming Code. · 2. Press ""Kwikset"" then ""1"" then ""Kwikset"" · 3. Enter a new User Code. · 4. Press ""Kwikset"" · 5. Test the code: While your door is open, lock it and enter your new User Code to make sure it unlocks the door.
Kwikset.com Home
2. How do I change the Programming Code on my 264 Deadbolt? - Kwikset
How do I change the Programming Code on my 264 Deadbolt? Make sure your door is open and unlocked 1. Enter your existing PC (Programming Code). 2. Press "Kwikset" then "4" then "Kwikset" 3. Enter a new PC. It must be between 4 and 10 digits. 4. Press "Kwikset" For all programming sequences, success is indicated ...
Make sure your door is open and unlocked1. Enter your existing PC (Programming Code).2. Press "Kwikset" then "4" then "Kwikset"3. Enter a new PC. It must be between 4 and 10 digits.4. Press "Kwikset"For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.
3. Support Information for Satin Nickel 264 Contemporary Keypad Deadbolt
How do I change the Programming Code on my 264 Deadbolt? ... Make sure your door is open and unlocked1. Enter your existing PC (Programming Code).2. Press "Kwikset" then "4" then "Kwikset"3. Enter a new PC. It must be between 4 and 10 digits.4.
Get support on 264 Contemporary Keypad
4. Support for Programming Code - Kwikset
How do I change the... · How to enable/disable... · On my Smartcode 955, I'm...
Kwikset.com Home
5. How do I add/delete a one-time User Code on my 264 Deadbolt? - Kwikset
1. Enter your existing PC (Programming Code). · 2. Press "Kwikset" then "9" then "Kwikset" · 3. Enter a new User Code. It must be between 4 and 10 digits. · 4. Press "Kwikset"
See AlsoThe Pros and Cons of ETFsKwikset.com Home
6. Support for Add One-Time User Code - Kwikset
How do I add/delete a one-time User Code on my 264 Deadbolt? A one-time user code may be used only once, and then it will be deleted immediately after ... Enter your existing Programming Code. 3. Press enter arrow. You will hear one beep. 4. Press 8. 5. Press enter arrow. You will hear one beep. 6. Enter a new ...
Kwikset.com Home
7. How to change Auto-Lock time delay on my 264 Deadbolt? - Kwikset
Enter your Programming Code. ... 3. Enter time between 10 and 99 seconds. ... For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps. If unsuccessful ...
Make sure your door is open and unlockedYou can set the Auto-Lock time delay between 10 and 99 seconds.1. Enter your Programming Code.2. Press “Kwikset” then “6” then “Kwikset”3. Enter time between 10 and 99 seconds.4. Press “Kwikset”For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.
8. Support Information for Satin Nickel 264 Traditional Keypad Deadbolt
264 Traditional Keypad Deadbolt · 264 Electronic Deadbolt Installation ...
Get Support on 264 Traditional Keypad